Some degree of water loss in a swimming pool or spa is to be expected during the course of usage. Water loss in these structures normally happens in three main ways. These ways include through backwashing the filters, splash out, or through evaporation. For those who live in hot areas, the amount of water loss due to evaporation can be very high. This is worth knowing about Queen Creek pool service.
With the abovementioned method of loss of water, it is normal that one should add at least 2 inches of water to the pool/spa each week. However, in case one has to add more than 2 inches each week, it is highly probable that there is a leak. This could be true if there is no other reason for the change in the speed of water loss in the structure.
For instance, it is to be understood that water evaporation may change depending on the season. Also, if the usage of the pool has increased in the recent past, then it may mean that water loss will also increase. However, if none of these has happened yet the loss of water seems to happen at a faster rate, then it may be time to be suspicious.
Before one decides to go further to contact a local pool technician, it is vital to confirm the suspicions one has. Several techniques can be employed to ascertain if indeed a leak actually exists. To confirm the presence of a leak, one should begin by inspecting the obvious. For example, one should make sure the leakage is not located at the equipment.
To ensure equipment is not leaking, one should take a close look at the pipe valves, pump, heater, and filter. One should also check the ground around the structure to ensure that it is not wet. One should walk around the structure to determine if there are any eroding or sunken areas. If all these seem to be okay, then it is time for the next step.
An alternative technique that can be employed to establish whether the structure is leaking is marking the water level inside the structure at the skimmer. This is made possible by use of grease, tape or pencil. Allow the pool a duration of 24 hours prior to coming back to assess the new level of the water.
An ordinary pool should lose about a quarter an inch of water each day. In case the drop in the level of water is higher than a quarter an inch, this could mean that a leak exists. Another way is to use a bucket with water filled to a similar level as the level in the structure. The bucket ought to be placed on top of the steps used when entering the structure.
The bucket ought to be left for a period of 24 hours after which it must be checked. In case the water in the structure has gone below the level of the water bucket, it implies there is a leakage. Water loss needs to occur at the same rate since both water in the structure and the bucket are subjected to evaporation equally.
With the abovementioned method of loss of water, it is normal that one should add at least 2 inches of water to the pool/spa each week. However, in case one has to add more than 2 inches each week, it is highly probable that there is a leak. This could be true if there is no other reason for the change in the speed of water loss in the structure.
For instance, it is to be understood that water evaporation may change depending on the season. Also, if the usage of the pool has increased in the recent past, then it may mean that water loss will also increase. However, if none of these has happened yet the loss of water seems to happen at a faster rate, then it may be time to be suspicious.
Before one decides to go further to contact a local pool technician, it is vital to confirm the suspicions one has. Several techniques can be employed to ascertain if indeed a leak actually exists. To confirm the presence of a leak, one should begin by inspecting the obvious. For example, one should make sure the leakage is not located at the equipment.
To ensure equipment is not leaking, one should take a close look at the pipe valves, pump, heater, and filter. One should also check the ground around the structure to ensure that it is not wet. One should walk around the structure to determine if there are any eroding or sunken areas. If all these seem to be okay, then it is time for the next step.
An alternative technique that can be employed to establish whether the structure is leaking is marking the water level inside the structure at the skimmer. This is made possible by use of grease, tape or pencil. Allow the pool a duration of 24 hours prior to coming back to assess the new level of the water.
An ordinary pool should lose about a quarter an inch of water each day. In case the drop in the level of water is higher than a quarter an inch, this could mean that a leak exists. Another way is to use a bucket with water filled to a similar level as the level in the structure. The bucket ought to be placed on top of the steps used when entering the structure.
The bucket ought to be left for a period of 24 hours after which it must be checked. In case the water in the structure has gone below the level of the water bucket, it implies there is a leakage. Water loss needs to occur at the same rate since both water in the structure and the bucket are subjected to evaporation equally.
About the Author:
Get excellent tips on how to pick a Queen Creek pool service company and more info about a reliable company at http://www.neptunepoolsaz.com right now.
0 comments:
Post a Comment