Walls that are constructed in a place so that they can support lateral force applied against them by soil are referred to as retaining walls. They offer lateral support, which allows soil to exist to varied levels on either side of the wall. This helps to maintain soil on slopes in positions. It would be otherwise hard to attain such differential in soil level without these structures. When one needs to make retaining walls Huntsville AL is a good location to find contractors.
These walls come in five main types even though there may be more types. The five main types are gravity, cantilevered, sheet piling, bored pile, and anchored. A gravity wall usually relies on its own weight to resist pressure placed on it by soil. To improve its stability, it may be constructed to look like a wedge. They can be made from a variety of materials and how they are constructed depends on many factors.
A cantilevered wall is usually made in the shape of an inverted capital letter T. They are designed to convert horizontal pressures resulting from the soil into vertical pressures on the ground. They may need to be buttressed to increase their ability to support load. It takes far much less material to construct a cantilevered wall as compared to a gravity one.
A sheet piling wall is suitable for use in tight spaces and soft soil. Construction is done using various materials, including wood planks, steel, and vinyl. These materials are driven into the ground at the proposed position of the wall. The construction material is driven so that 66 percent of the length goes into the ground while only 33 percent remain above the ground. The length of material driven into the soil can be varied depending on various factors.
A bored pile retaining wall is constructed by collecting a series of bored piles after the excavation of excess soil. Materials like reinforcing beams, reinforcement layer, shot crete, soil improvement operations and earth anchors can also be added in the setup. In situations where sheet piling is used as a construction solution, then this method is practical but due to noise levels one cannot use pile drivers.
Anchored wall is applicable in various construction settings. The wall is anchored into the soil behind it using cables. Installation of the cable can be done using various methods. It takes technical expertise to be able to install the anchors properly, especially if the soil load involved is huge.
There are several purposes that are served by a retaining wall. First, it helps to maintain soil in place. It is possible for excess soil to be lost near the foundation of a building, causing major problems. The wall does not only add value to the property, but it prevents damage and saves the homeowner money in future.
These structures are also suitable for preventing soil erosion. This is especially important for people who do farming on slopes. Being able to keep soil in place helps plants to attain deep roots. Thus, productivity improves a lot. Slopes can experience harsh soil erosion if steps are not taken to prevent it.
These walls come in five main types even though there may be more types. The five main types are gravity, cantilevered, sheet piling, bored pile, and anchored. A gravity wall usually relies on its own weight to resist pressure placed on it by soil. To improve its stability, it may be constructed to look like a wedge. They can be made from a variety of materials and how they are constructed depends on many factors.
A cantilevered wall is usually made in the shape of an inverted capital letter T. They are designed to convert horizontal pressures resulting from the soil into vertical pressures on the ground. They may need to be buttressed to increase their ability to support load. It takes far much less material to construct a cantilevered wall as compared to a gravity one.
A sheet piling wall is suitable for use in tight spaces and soft soil. Construction is done using various materials, including wood planks, steel, and vinyl. These materials are driven into the ground at the proposed position of the wall. The construction material is driven so that 66 percent of the length goes into the ground while only 33 percent remain above the ground. The length of material driven into the soil can be varied depending on various factors.
A bored pile retaining wall is constructed by collecting a series of bored piles after the excavation of excess soil. Materials like reinforcing beams, reinforcement layer, shot crete, soil improvement operations and earth anchors can also be added in the setup. In situations where sheet piling is used as a construction solution, then this method is practical but due to noise levels one cannot use pile drivers.
Anchored wall is applicable in various construction settings. The wall is anchored into the soil behind it using cables. Installation of the cable can be done using various methods. It takes technical expertise to be able to install the anchors properly, especially if the soil load involved is huge.
There are several purposes that are served by a retaining wall. First, it helps to maintain soil in place. It is possible for excess soil to be lost near the foundation of a building, causing major problems. The wall does not only add value to the property, but it prevents damage and saves the homeowner money in future.
These structures are also suitable for preventing soil erosion. This is especially important for people who do farming on slopes. Being able to keep soil in place helps plants to attain deep roots. Thus, productivity improves a lot. Slopes can experience harsh soil erosion if steps are not taken to prevent it.
About the Author:
When you are looking for information about retaining walls Huntsville AL residents can come to our web pages online today. More details are available at http://www.hislandscapes.com now.
0 comments:
Post a Comment