Beautify landscaping can take many different forms in order to take a rather plain looking yard and turn it into something spectacular. A popular way is to install some sort of water display. With a pondless waterfall kit, you can do just that. Built correctly, you end up with a natural looking fall and stream that recycles the water for continuous pleasure.
The beginning of the project requires mapping out how you want it to look and marking the yard. Once you have your plan, use bright spray paint to mark the areas that you need to dig. You will need to map out where the reservoir, or bottom, of the display will be, including where the pump will go.
When you dig, there are several things that need to be done just right. First, the reservoir needs to sit below the stream path. You will want to dig 18 to 24 inches deep and in a large square or circle. Then you will need to dig a deeper hole to place the pump vault. This needs to be the lowest point of the reservoir in order for all the water to be recirculated. Save the dirt to use for fill and covering the pipe and lining.
The lining should be installed next. Place it in the reservoir. It is suggested that you use more than one layer to make sure it doesn't get punctured and leak water into the ground. With the middle hole deeper, place the vault and install the pump in the vault.
Attach the flex hose to the pump and run it uphill. If you want to dig a trench to bury the hose, you may at this point, but you should have enough dirt to bury it without a trench. It is best to keep it uncovered until the last step. This hose will be hooked up to the spillway to create the water flow.
You need to use large gravel to fill in the reservoir and then larger rocks to begin building the stream. These will be placed in various intervals along the rubber liner. The entire stream and system should be on top of the liner so you don't lose the water along the way. It will also keep the yard from being washed out. You are basically building a self-contained system.
The larger boulders can be used in various points to create additional spillways and paths. When these are in place, begin filling in areas with different types of rocks and gravel for decorative purposes and to create a natural stream. Before you're done, run water through the system to see where the water path will go and adjust the rocks and liner as needed.
After everything is in place, continue filling in the stream with the rocks and cover the liner and tubing with the extra dirt. Several inches of dirt should be used to allow you to plant things along the path. Other items can be placed to help make it look more natural.
The beginning of the project requires mapping out how you want it to look and marking the yard. Once you have your plan, use bright spray paint to mark the areas that you need to dig. You will need to map out where the reservoir, or bottom, of the display will be, including where the pump will go.
When you dig, there are several things that need to be done just right. First, the reservoir needs to sit below the stream path. You will want to dig 18 to 24 inches deep and in a large square or circle. Then you will need to dig a deeper hole to place the pump vault. This needs to be the lowest point of the reservoir in order for all the water to be recirculated. Save the dirt to use for fill and covering the pipe and lining.
The lining should be installed next. Place it in the reservoir. It is suggested that you use more than one layer to make sure it doesn't get punctured and leak water into the ground. With the middle hole deeper, place the vault and install the pump in the vault.
Attach the flex hose to the pump and run it uphill. If you want to dig a trench to bury the hose, you may at this point, but you should have enough dirt to bury it without a trench. It is best to keep it uncovered until the last step. This hose will be hooked up to the spillway to create the water flow.
You need to use large gravel to fill in the reservoir and then larger rocks to begin building the stream. These will be placed in various intervals along the rubber liner. The entire stream and system should be on top of the liner so you don't lose the water along the way. It will also keep the yard from being washed out. You are basically building a self-contained system.
The larger boulders can be used in various points to create additional spillways and paths. When these are in place, begin filling in areas with different types of rocks and gravel for decorative purposes and to create a natural stream. Before you're done, run water through the system to see where the water path will go and adjust the rocks and liner as needed.
After everything is in place, continue filling in the stream with the rocks and cover the liner and tubing with the extra dirt. Several inches of dirt should be used to allow you to plant things along the path. Other items can be placed to help make it look more natural.
About the Author:
Get a summary of the factors to consider when choosing a pondless waterfall kit supplier and more information about a reputable supplier at http://www.boulderfountain.com/pondless-waterfall.html now.
0 comments:
Post a Comment