These operators are devices that enables you to access gates just by using a keypad or an intercom. They are very much alike to garage door openers. Therefore if you wish to install one then you should know that it is similar to installing a garage door. There are various gate operators including the Doorking gate operators which unlike others, is designed to control vehicular swing gates in commercial and residential places. However, before starting the installation process you first need to contact your local utility company to confirm that there are no underground lines where you will be digging. You also need to ensure that you have the correct tools and materials for the job.
But before you consider installing your operator, you first have to ensure that there are none underground lines existing at the place where you are going to do your digging. You can find out this by contacting local utility companies. Secondly, you need to get the right tools and the materials for the installation process.
If you have all that is required, then you are ready for the job. First, you need to find the correct place for the control box. You might just want to drill some holes where the control box will be placed on your fence, then connect the arm to the control box. This will entirely depend on the style of your fence.
After you have gathered all the requisite equipment, then you are ready to get it installed. First and foremost, you need to drill holes through your holes where you will attach your control box. After doing this, you need to connect the arm to the control box. This however depends on the design of the gates. But in some operators like the doorking gate operator, the arm is connected to the bottom rail of the gate because of its unique design.
You must dig a thin trench, which should not be less than 9 inches deep and not more than a foot deep. The trench should start from the breaker panel and end at the gates. The electric pipe should be placed inside the trench but through the PVC pipe. All these should be done while the power switch is off.
Connect the wires to the control box of course with the power switch still off. You should then connect the sensor to the fence so as to make it free and clear from any impending damages. The wires from the sensor should be clipped alongside so that they do not become loose.
With all these done, you can consider the installation process complete but your success will be determined by how good it operates. If it opens and closes easily then consider your work a complete success.
This thus shows how it would not be wise of you to hire someone else to do the installation process for you when you can as well install your gate operator with ease just by following the simple instructions that have been outlined above. This is the easiest way through which people will be able to benefit from these operators.
But before you consider installing your operator, you first have to ensure that there are none underground lines existing at the place where you are going to do your digging. You can find out this by contacting local utility companies. Secondly, you need to get the right tools and the materials for the installation process.
If you have all that is required, then you are ready for the job. First, you need to find the correct place for the control box. You might just want to drill some holes where the control box will be placed on your fence, then connect the arm to the control box. This will entirely depend on the style of your fence.
After you have gathered all the requisite equipment, then you are ready to get it installed. First and foremost, you need to drill holes through your holes where you will attach your control box. After doing this, you need to connect the arm to the control box. This however depends on the design of the gates. But in some operators like the doorking gate operator, the arm is connected to the bottom rail of the gate because of its unique design.
You must dig a thin trench, which should not be less than 9 inches deep and not more than a foot deep. The trench should start from the breaker panel and end at the gates. The electric pipe should be placed inside the trench but through the PVC pipe. All these should be done while the power switch is off.
Connect the wires to the control box of course with the power switch still off. You should then connect the sensor to the fence so as to make it free and clear from any impending damages. The wires from the sensor should be clipped alongside so that they do not become loose.
With all these done, you can consider the installation process complete but your success will be determined by how good it operates. If it opens and closes easily then consider your work a complete success.
This thus shows how it would not be wise of you to hire someone else to do the installation process for you when you can as well install your gate operator with ease just by following the simple instructions that have been outlined above. This is the easiest way through which people will be able to benefit from these operators.
About the Author:
Feel free to browse around our official website to learn more about Doorking gate operators. To get further information, click on the contact button of this page http://www.eastcoastgateoperatorsinc.com.
0 comments:
Post a Comment